Jedidiah SAL – Supplex w/ an elasticated waist

The sewing for this version of the Jedidiah shorts is pretty quick so we decided working it up in a photo blog would be better than incorporating it into the video series. There are still videos for the welt pockets and zipper fly but the rest of the sewing will be demonstrated in the photos.

For this version I created a welt pocket for one side of the back and then used an elasticated waist along with supplex for a more casual fit. In using a super stretchy fabric like supplex you can size down but I wanted to keep a straighter leg line so I opted to go with his measured size.

https://pheefabrics.com/supplex/

Altering Pattern Pieces

The first step to this was altering the pattern pieces. Attach the back yoke to the back pants piece overlapping the seam allowance (5/8") and cutting into the top of the back yoke piece so it can lay flat.

The first step to this was altering the pattern pieces. Attach the back yoke to the back pants piece overlapping the seam allowance (5/8″) and cutting into the top of the back yoke piece so it can lay flat. Mark 5/8 inch down on the back pants piece then line up the bottom of the yoke piece with those marks.

Then you can cut out all of your pattern pieces. Everything is the same as the original pattern except I DO NOT interface the entire waistband.

Make sure to mark all of the notches and if you’re doing the welt pockets the two top pocket placement notches shown here.

Welt Pockets

Next is to work on the welt pockets. You’ll need these size pieces:

For a 6 inch pocket

7-1/4 x 6in in main fabric

7-1/4 x 5-1/4in in main fabric

7-1/4 x 2-1/2in in main fabric and interfacing fused with an additional interfacing for the pants piece

I opted to only do one side with a welt pocket to emulate these rtw shorts travis has but you can do it on both sides easily enough.

Next is the front slat pockets. Supplex is a thick heavier fabric that does allow the shorts to look more professional but can also add bulk if you’re not careful. Since it is so thick I decided not to use the facings for these shorts.

Slat Pockets

For the next step, finishing the bottom of the pocket, the directions used french seams. I found this to be too bulky for the supplex so I opted to just serge the pocket bottom with right sides together.

Now the front of the pants are complete we can attach the front and back of the pants.

Inseam and side seams

The directions instruct us to use flat felled seams or french seams for the inseam and side seam but I don’t find this necessary when doing these in supplex. I serged both seams using the 5/8 inch seam allowance.

I opted to not use bar tacks on the pockets when using supplex.

You can hem now or at the very end I chose to hem at the very end.

Next I sewed the crotch seam. There is a notch on the fly part of the front pants piece make sure this is marked. Then we need to finish the edges of the crotch seams. I opted to serge these edges. When you sew the crotch seam we sew from the center back down to the inseam and then up until you’re 1/2 inch below that notch we marked.

When you get to sewing up into the fly section of the crotch seam you sew directly from the 5/8 inch seam allowance straight up to the point you marked 1/2 inch below the notch. You do not follow the curve of the fly.

Fly

Next we’ll be stitching the fly. There will be a video for this!

FLY VIDEO WILL BE INSERTED HERE]

Waistband

The first step for the waistband is to interface the ends. I used a 4×4 square of interfacing and reinforced both ends of the waistband. I then serged one of the long raw edges and ironed the waistband in half wrong sides together length wise.

To attach the waistband clip the non-serged edge of the waistband to the top of the pants with right sides together with the short raw edges of the waistband hanging over the zipper fly/facing edges by 5/8 inch. Sew the waistband to the main pants distributing evenly.

We’re now going to enclose the waistband starting with the 5/8 inch overlap. Fold the waistband in half right sides together matching the short raw edge.

Pull the main pants, where the zipper is, away from where you just clipped and line up the raw edge of the waistband with the serged edge making sure not to catch the main pants.

Now pull the main pants out of the waistband so it is right sides out.

Now flip the pants so you’re looking at the back side and we’re going to fold the waistband down using the memory seam we created earlier. Pin the serged edge to main pants enclosing the seam allowance we previously created and using the memory crease to keep the fold even.

With the right side out topstitch along the edge of the waistband catching the back side of the waistband. I used a triple stretch stitch and started 6 inches from the waistband edge all the way around to 6 inches from the opposite short edge.

I measured the distance that I topstitched and subtracted a couple inches to get a rough idea of how long I wanted my elastic to be. Attach a safety pin to one end of the elastic and feed it through the casing. Then, tack the end of the elastic down 3 inches from the short end of the waistband.

Once you have fed the elastic all the way through you can guide it out of the other end and try on to measure exactly how long you want the elastic.

Now we can finish up the topstitching. From your previous topstitch line continue to the inside edge of the waistband.

We’re almost done!

Button and buttonhole

Last is hemming!

I serged the raw bottom edge of the shorts and then folded wrong sides together and zig zag stitched 1/2 inch from the bottom.

You are finished!! Yay!!

One comment

  1. Awesome, I need to make a pair for DH. The buttonholes on most machines are a mess. I bought a juki f600 (since berninas were too much) just for the button holes. I celebrated its arrival with a Thread Theory Fairfield for DH. The perfect, identical buttonholes are a thing of beauty.

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.